Rod seal factory manufacturer right now in 2024: Types of Mechanical Seals – Several types of mechanical seals are available. Some of the popular ones include: Balanced and unbalanced seals; Pusher and non-pusher seals Cartridge seals. A mechanical seal consists of rotary and stationary faces running against each other. These faces apply a closing force against each other using springs and the pressure generated from the process fluid. This way, a seal is formed to prevent the fluid from leaking between the rotating shaft and the pump housing. Mechanical seals can be selected based on the type of pump application. Choosing the wrong seal can affect pump performance and lead to damage and costly repairs. An unbalanced mechanical seal is preferred if the pump needs to operate at a lower pressure. However, high pressure pumping applications require balanced mechanical seals. Balanced seals also perform better in high temperature operating conditions. Cartridge seals require less maintenance but are more expensive, hence used for limited applications. Read even more info on spring seals.
The Fluid Film – In most mechanical seals the faces are kept lubricated by maintaining a thin film of fluid between the seal faces. This film can either come from the process fluid being pumped or from an external source. The need for a fluid film between the faces presents a design challenge – allowing sufficient lubricant to flow between the seal faces without the seal leaking an unacceptable amount of process fluid, or allowing contaminants in between the faces that could damage the seal itself. This is achieved by maintaining a precise gap between the faces that is large enough to allow in a small amounts of clean lubricating liquid but small enough to prevent contaminants from entering the gap between the seal faces. This micro-gap is maintained using springs and hydraulic force to push the seal faces together, while the pressure of the liquid between the faces (the fluid film) acts to push them apart.
According to the material, DMS Seals’s products are divided into several categories, and oil seals are one of them. Oil seal has the following advantages: well-chosen materials, reasonable design, stable performance, excellent quality, and affordable price. Such a product is up to the market demand. DMS Seals has been focusing on all kinds of rotary shaft seals, bulk oil seals wholesale, and also can custom oil seals according to customers’ requirements. If you are looking for a professional oil seal manufacturer and reliable oil seal supplier, welcome to contact us.
The rod seal is the most important sealing component designed by DMS SEALS in the liquid sealing application. It can effectively prevent the liquid inside the cylinder from leaking to the outside. Moreover, if there is a leakage problem in the rod seal, the performance of the equipment will be degraded. There are even some machine and human safety issues in extreme cases. This type of seal meets the standards of GB/T 15242.1-94 and GB/T 15242.3-94. It is ideal for high and low-speed reciprocating rods and rods in high-pressure system cylinders. Moreover, it can be used in a variety of fluids and high-temperature environments. It is characterized by its high corrosion resistance and its ability to work well in a corrosive media with no oil spots. It has high stability under pressure and harsh conditions. The outstanding advantages of our seals are strong wear resistance, resistance to extrusion, low friction and no stick-slip.
Destroy the leak: The working conditions of the sealing part are relatively bad, the thermal deformation is large, it is often subjected to vibration, impact, improper installation, excessive tightening force, repeated use, compression deformation, internal stress concentration, damage beyond the fatigue strength, material aging, deterioration, etc. will cause damage to leaks. This kind of leakage has the greatest impact and great harm, so it is necessary to strengthen prevention.
Support and positioning The piston and piston rod are radially supported and positioned in the cylinder barrel. Isolate the two pairs of motion pairs of piston and cylinder, piston rod and guide sleeve to prevent direct scratches, abrasions and strains between the motion pairs. Especially when the motion pairs are all steel parts, they must be isolated, otherwise they will be easily strained. The guide belt also has an important role to reduce the friction and friction work between the moving parts, reduce the ineffective work and heat. Vibration absorption and noise reduction Reduce system vibration and noise. It is mainly filled with tetrafluoroethylene and phenolic cloth, and there are also a very small amount of polyoxymethylene, nylon and soft metal. Discover more information at dmsseals.com.
DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.
Construction machinery sealing system requirements: High and low temperature resistance Because of continuous work for a long time, if it is outdoors in summer, the hydraulic oil temperature of the machine may exceed 100°C, which requires the seal to be resistant to high temperature. If it is outdoors in winter, the temperature may be around -40°C when it is just turned on, and the seals are required to be resistant to low temperatures. Therefore, the sealing system is required to withstand a wide temperature range. The machine itself walks. Due to the limitation of volume and weight, the hydraulic oil tank is generally relatively small.
The O-ring of DMS SEALS is often used in hydraulic and pneumatic transmission systems and has wide applications. It can be used for both static and reciprocating seals. Moreover, it can also be used in rotary sealing systems. The O-ring can be installed in a groove with a rectangular cross section on the outer or inner circle, achieving a good sealing effect. It has many advantages compared with other types of sealing rings. Its compact structure makes it easy to assemble and disassemble. Moreover, its dynamic frictional resistance is relatively small, and a single piece of O-ring can achieve sealing performance in both directions.